FE1 is the "Corvette Standard Suspension" and FE3 is the "Corvette Sport Suspension." There are two sub-levels of shocks available on the FE1. Mar 31, 2021. grandville75 said: Hi All, I'm new to the Impala Forum and have a Rack and Pinon assy question. Fits FE1 Soft Ride Suspension and FE3 Sport Suspension; Fits FE3 Sport Suspension; 2005-2006 Pontiac Pursuit Fits FE3 Sport Suspension; For the driver side use rk620898. I always drove around in track, because I like that planted, aggressive feeling. . Like mp81 said, 08+ fe5 control arms won't work but any other control arm will swap in no problem and any of the shock/strut and spring combos will work. The annual repair and maintenance cost for this model is approximately $540. At its most basic, the C5 and C6 Corvette suspension uses upper and lower A-arms suspended by transverse leaf springs made of fiberglass. Lifetime, annual contributors, and 24 year members of National Corvette Museum. What is the best bitrate for YouTube videos? What SINSTR6 said, my understanding is that the only difference is thicker swaybars, springs and shocks are the same. . Don't be surprised to buy a fairly new used car, and you find that it has a blocked warranty. FE2 usually sits 1-1.5 inches lower than standard, beats driving around in a 44. Posted January 2, 2021. No Upfront Core Deposit . And thats lower than the average for other vehicle models, which is $650. Aperu rapide Available . It has been done plenty of times, whatever company you talked to telling you it won't work is just going by what their system tells them your car needs. Rear Swaybar on Sedans is increased in size from 18mm to 20mm which still isnt big enough. Currently Active Users Viewing This Thread: 1. The FE1 doesn't obviously but.. I then keep those reports in my file for each car. ACNA Notice Board. . check out the. That is free to try! . Z85 Designed for enhanced handling and trailer towing, with monotube front and rear shocks. On a base suspension car, you will only find the code FE1. FE1 came with all base models and are the "softest" SS/NA came with FE3 and are a bit stiffer. google_ad_height = 90; The lower control arms on the FE1 suspension are steel, while on the FE3 suspension, they are aluminum, but they are dimensionally the same. I swapped the full 96 monte carlo suspension into the rear of the car, and am now deciding if I should just swap the entire front, or just a few select pieces. As a follow-up I checked GM front and rear spring part numbers and found that there are different spring part numbers for Stingrays without MRC (FE1 suspension), Stingrays with MRC (FE2 suspension), Z51's without MRC (FE3 suspension), Z51's with MRC (FE4 suspension), Z06's without Z07 (FE 6 suspension) and Z06's with Z07 (FE 7 suspension). FE2 Suspension question. The struts on the FE1 suspension offer a softer ride than that on the FE3 suspension, but they are dimensionally the same. /* 728x90, created 4/10/11 */ While the FE3 is with sport suspension performance driving type (made up of aluminum). FE2: Mag-Ride on Base Suspension. theres a sticker in the trunk under the mat on the left side. I do think the design was improved, though, as my first set didn't make it 30k, and these have over 40 on them with no collapse. I have an early 2003 Ion and most of the control arms I see advertised seem to be for FE1 Suspension which my car does not have. FE3 ( LTZ and SS): Impala LTZ and SS models receive a FE3 suspension, which includes 18-inch W-rated P235/50R18 AL3 (performance) tires and five-spoke alloy wheels, to provide a sporty ride that complements the 5.3L small-block V-8s performance. ALL MODELS EXCEPT VEHICLES WITH FE3 SUSPENSION. During the time the 91-96 B-body was built, there eventually were a total of 7 different suspension codes employed, depending on how the order form was marked and when the car was built. FE2 = the option code for the base suspension. FE3 = option code for uplevel suspension. WS6 was also a suspension package on the 80s Firebirds. I want to put the FE3 suspension on because it looks nicer and runs a little more to my liking. Copyright 2018-2022 MidEngineCorvetteForum.com. Rear Stabilizer Bar (mm) - Base and F45 suspension 19.1x2mm The Z51 Bar is 21.7x3mm. I am just trying to figure out what the difference is between the ones for 80 dollars and the ones for 140 dollars. This page was generated at 07:39 AM. FE1,FE2,FE3 are grouped together and then FE5 is alone. You could contact any GM dealer, give service writer or parts guy your vin. Jul 1, 2006. So, I decided to just go with Z51 and no magride. see if it says fe1,fe3, or fe5 on it. vc commodore. (stiffer suspension, better handling etc). Im leaving to somewhere soon and ill be gone for a long time. What is the Difference Between Moog R Series and CK Control Arms? How long do struts last on a Chevy Impala? Still not up to scratch with a good aftermarket spring/shock combo - but a step in the right direction at least. My previous Vette was a C7 Z06 with Mag ride.